Lister LD, SL, SR, SRW & ST engines.
A general purpose fuel tank cap.
Bayonet fitting, dimensions as per the picture.
Ideal as a cost effective replacement where the sizes are suitable.
New Genuine Lister LD Internal Governor Springs
Lister part number 201-10821
These springs are new old stock and in good condition, supplied in original Lister packaging.
A Lister fuel tank cap.
Lister P/N 366-08136 which supersedes P/N 027-03824 and 366-00091
Fitted to a wide range of Lister fuel tanks.
Suitable for use with HA and HR models.
Lister HA cylinder head shim.
Lister P/N 351-10370
A genuine Lister HL, HR4 & HR6 flywheel end felt crankshaft oil seal.
Lister P/N 354-50360
Lister HR cylinder head shim.
Lister P/N 351-50191
Lister HRW4, HRW6 and HRWS6 radiator cooled engine alternator belt.
Lister P/N 354-44870
Lister oil reservoir / priming cup.
Lister P/N 201-26480
A genuine Lister inlet manifold for reverse rotation SR1 engines.
This manifold sweeps to the left above the exhaust which is not standard spec which was out to the right on P/N 201-51122 but this manifold P/N 570-11290 is for reverse rotation engines and is a slightly different shape.
A genuine Lister inlet manifold for standard rotation SR1 engines.
Lister P/N 201-51122
A genuine Lister ST1 and ST2 fuel pipe.
Lister P/N 366-06746
This pipe is fitted between the fuel tank and the fuel agglomerator on Lister ST1 and ST2 engines.
A genuine Lister ST3 fuel pipe.
Lister P/N 203-82880
Petter AB1, AC1 & AD1 Flywheel End Crankshaft Oil Seal.
Lister Petter part number 363686
Petter AB1, AC1 & AD1 Gear End Crankshaft Oil Seal.
Lister Petter part number 359423
Aluminium cooling fin sleeve for use with 99/235 type injectors fitted to Petter PAZ1 engines.
Genuine Lister Petter part number 208485.
For later engines using cooling fin sleeve P/N 272376 which is compatible with Bryce injector code 99/320, NSDLA067D0468 or BKB50S5188 with parallel fixing stud positions.
These will not fit the early engines pre serial number 2455 which use Bryce injector code 99/236 Petter P/N 265585 using offset fixing stud positions.
For early engines using cooling fin sleeve P/N 292004 or CB85 which is compatible with Bryce injector code 99/236 Petter P/N 265585 using offset fixing stud positions.
These will not fit the later engines post serial number 2455 which use Bryce injector code 99/320, NSDLA067D0468 or BKB50S5188 with parallel fixing stud positions.
A genuine Petter inlet manifold.
Petter P/N CF32 or 296165
Suitable for single cylinder engines only.
A genuine Petter PJ1 water inlet manifold.
Petter P/N WCF28
Suitable for single cylinder engines only.
A genuine Petter PJ2 inlet manifold.
Petter P/N CF43 or 296164
Suitable for twin cylinder engines only.
A genuine Petter PJ2 inlet manifold for use when an oil bath air cleaner is fitted.
Petter P/N CF43D
Suitable for twin cylinder engines only.
Petter P/N 336250
Genuine Petter PU anti friction collar in original protective packing dating from April / May 1958
Petter part number SFX/D110/9
Packet says 5/8" diameter outside tube. Part consists of a thick brass or bronze washer with a chamfer to the internal diameter on one side.
Genuine Petter PU exhaust valve in original protective packing dating from April / May 1958
Petter part number 59855
Genuine Petter PU inlet valve in original protective packing dating from April / May 1958
Petter part number 59856
Genuine Petter PU compression piston rings in original protective packing dating from April / May 1958
Petter part number 4-59958
For 75mm bore diameter which is 2.95"
Genuine Petter PU valve tappet in original protective packing dating from April / May 1958
Petter part number 3-82465
Genuine cylinder kits for Lister LR engines.
These cylinder kits comprise of:- 1 x Cylinder P/N 201-70110 and 1 x Piston assembly P/N 570-11308
The piston assembly includes the rings, gudgeon pin and circlips.
Lister HA4, HR4, HR6, HRS6 and JK6 oil filter element.
Lister Petter P/N 291-40910
Alternative OEM P/N Purolator MF43A, Tecalemit FG.2326 & FG.2457, Fram CH.869PL, G.U.D G.524
A Petter "A" series rope start pulley guards.
There are three types available.
Petter P/N AAL434 or 298010 is suitable for Petter AA1, AB1 and AC1 series 1 engines - gear end starting in red or green.
Petter P/N AAL434A or 296520 is suitable for Petter AA1, AB1 and AC1 series 1 engines - flywheel end starting in green.
Please select the option required from the menu when ordering.
These are genuine Petter items but older stock so may have signs of long term storage etc but will not affect the operation.
A genuine Petter "A" series rope start pulley for flywheel end starting.
Petter P/N AAL411 or 405101.
Suitable for Petter AA1, AB1 and AC1 series 1 engines.
These are genuine Petter items but older stock, they have a slightly aged appearance but this will not affect the operation and would clean up with little effort.
Genuine Lister LR piston assembly.
Piston assembly P/N 570-11308
The piston assembly includes the rings, gudgeon pin and circlips.
A 5/16" Whitworth grub screw 3/4" long which is the correct size for locking the original 8" diameter A section cast iron V belt pulley with a 3/4" bore onto the crankshaft of the Lister domestic type water pump.
Lister P/N 201-80210
A replacement pawl spring for Petter starting handles.
Petter P/N 251959 which is now superseded by 367820
Lister LV2 engines
Genuine Lister LR piston assembly 0.010" over size.
Piston assembly P/N 570-11308/010
The piston assembly includes the rings, gudgeon pin and circlips.
As used on Lister LD, LR, SL and SR engines to mount filter assembly on P/N 201-11613, 201-11614 or 201-11615.