These cylinders are not interchangeable with early engines despite both using the same piston assembly P/N 359972.
Cylinder differences:-
Early style P/N 402442 base spigot OD is 109.44 mm ( 4.309”)
Later style P/N 402443 base spigot OD 104.90 mm ( 4.130”)
Please check your requirements carefully before ordering to ensure compatibility.
Head gasket for Petter PJW engines.
Petter part number 287750 and WCB58
A top end gasket set suitable for the Petter PJ1, PJ2, PJ1Z, PJ2Z, PJ3 and PJ4 engines.
Equivalent to Petter part number 359500.
A bottom end gasket set suitable for the Petter PJ1, PJ1Z, PJ2, PJ2Z and PJWZ engines.
Equivalent to Petter part number 344108.
Petter PJ gear end / extension shaft oil seal.
Equivalent to Petter part number 265654.
Petter PJ flywheel end oil seal.
Equivalent to Petter part number 314664.
A replaceable dry paper element type air filter assembly suitable for use on a huge variety of engines but especially Lister Petter engines.
Lister LD, LR, LPA, LPW, LPWS, SL, SR, ST, VA, Later 31/2 -1. 6-1, 8-1, 12-2 and 16-2 engines.
Petter AA, AB, ABW, AC, ACW, AD, P600, PH, PHW, PJ, PJW engines.
For early engines using cooling fin sleeve P/N 292004 or CB85 which is compatible with Bryce injector code 99/236 Petter P/N 265585 using offset fixing stud positions.
These will not fit the later engines post serial number 2455 which use Bryce injector code 99/320, NSDLA067D0468 or BKB50S5188 with parallel fixing stud positions.
For later engines using cooling fin sleeve P/N 272376 which is compatible with Bryce injector code 99/320, NSDLA067D0468 or BKB50S5188 with parallel fixing stud positions.
These will not fit the early engines pre serial number 2455 which use Bryce injector code 99/236 Petter P/N 265585 using offset fixing stud positions.
These 8mm 1/559 elements are suitable for use in Bryce FAOABO80C0210, FAOABO80C0280 and FAOABO80CO770 fuel pumps as commonly used on Petter PH, PHW and PJ single and multi cylinder engines.
Good quality compact tractor style exhaust silencers as used on our Petteroid engine powered pump and generator sets etc.
These silencers could be used for any engine in need of a well made exhaust silencer that will accept the 2" bore pipe which clamps down at the base.
Overall length is 25" and the diameter of the main body section is approximately 3.5". Supplied with a suitable D clamp.
High quality big end bearing shell sets for the well known Petter PH and PJ Diesel engines.
Available in a range of sizes, please select the size required when ordering.
Equivalent to Lister Petter part number 392989. You will need to purchase one set per big end, i.e two sets for a twin cylinder engine.
Petter style starting handles suitable for engines using 1.5" crankshaft diameters with a keyway to provide a location point for the ratchet pin housed in the starting handle to engage with.
Equivalent to Petter part number 193374.
Petteroid starting handles suitable for engines using 1.5" crankshaft diameters with a keyway to provide a location point for the ratchet pin housed in the starting handle to engage with.
Similar to Petter part number 193374 and can be used on genuine engine as well as the Petteroid copies.