Cartridge Fuel Filter Element - P/N 201-13118
A replacement fuel filter element for the cartridge fuel filter assembly fitted to many Lister Petter engines.
Equivalent to Lister Petter P/N 201-13118
Fitted to a wide range of Lister Petter engines including but not limited to the AA, AB, AC and AD series, the LT, LV series, some early TS engines, most LD, LR, SL, SR, ST1, ST2, Petter PH, PJ, P600 and PAZ1 engines.
Dimensions are O.D. 55mm x I.D. 23mm x H 37mm
Many seasoned Lister Petter engine owners will recognise this as the element ACD60 for use in standard AD600 type filters.
£5.10
including VAT
Lister Petter Fuel Filter Assembly - P/N 284359
The later type of cartridge fuel filter assembly used widely across the Lister Petter range, including engine series:-
Lister LD, LR, LPA, LPW, LPWS, SL, SR, ST, VA, Later 31/2 -1. 6-1, 8-1, 12-2 and 16-2 engines.
Petter AA, AB, ABW, AC, ACW, AD, P600, PH, PHW, PJ, PJW engines.
Lister LD, LR, LPA, LPW, LPWS, SL, SR, ST, VA, Later 31/2 -1. 6-1, 8-1, 12-2 and 16-2 engines.
Petter AA, AB, ABW, AC, ACW, AD, P600, PH, PHW, PJ, PJW engines.
Fitted with an aluminium top cover and a bowl to house the replaceable paper filter element. The top cover is female threaded to accept 1/4" BSP male unions at either side.
Equivalent to Petter P/N 95713, 284359, ASE64, ASE64A, AD600, 201-11613, 201-11614 and 201-11615
Many seasoned Lister Petter engine owners will recognise this as the standard AD600 type filter which accepts the common ACD60 paper element which is now known on P/N 201-13118 which is available separately if required.
£16.22
including VAT
Petter PH1 Fuel Pipe - Filter To Pump P/N 262936
A quality reproduction fuel pipe for the Petter PH1 engine equivalent to P/N 262936.
This pipe runs between the fuel filter and the fuel pump. The pump end swivel union fitting is threaded M14 x 1.5 and the filter end is supplied with a 1/4" BSP straight union, total pipe length is approx 15.5".
Supplied as a kit comprising of pipe, swivel union bolt and sealing washers.
Suitable for single cylinder engines only.
£24.00
including VAT
Petter PH2 Fuel Pipe - Filter To Pump P/N 262936
A quality reproduction fuel pipe for Petter PH2 engines.
Equivalent to Petter P/N 262936.
This pipe runs between the fuel filter and the fuel pump. The pump end is supplied with a M14 x 1.5 straight union and the filter end is swivel union fitting in 1/4" BSP, total pipe length is approx 15.5".
Supplied as a kit comprising of pipe, swivel union bolt and sealing washers.
Suitable for twin cylinder engines only.
£24.00
including VAT
Petter AV, AVA & Early PH Fuel Pipe - Pump To Injector P/N 198313
Click here
to subscribe for 'Back-in-stock' notifications
Petter AV, AVA and early PH high pressure fuel pipes for connection between the fuel pump and injector.
Equivalent to Petter P/N's JE34 and 198313
Suitable for:-
Petter AV2 flywheel end - twin cylinder engines only
Petter AVA1 & AVA2 gear end
Petter PH2 (early) flywheel end - twin cylinder engines only
£41.42
including VAT
Click here
to subscribe for 'Back-in-stock' notifications
Petter AV, AVA & Early PH Fuel Pipe - Pump To Injector P/N 198314
Petter AV, AVA and early PH high pressure fuel pipes for connection between the fuel pump and injector.
Equivalent to Petter P/N's JE35 and 198314
Suitable for:-
Petter AV1 & AV2 gear end
Petter AVA2 flywheel end - twin cylinder engines only
Petter PH (early) flywheel end - twin cylinder engines only
£33.91
including VAT
Petter PH Fuel Pipe - Pump To Injector
Petter PH high pressure fuel pipes for connection between the fuel pump and injector.
Equivalent to Petter P/N's HJE34 and 294578
Suitable for:-
Petter PH1 (late)
Petter PH2 (late) gear end - twin cylinder engines only.
£25.40
including VAT
Petter PH2 Fuel Pipe - Pump To Injector
Petter PH high pressure fuel pipes for connection between the fuel pump and injector.
Equivalent to Petter P/N's HJE35 and 294579
Suitable for:-
Petter PH2 (late) flywheel end - twin cylinder engines only.
£25.40
including VAT
Genuine Lister Petter PH Governor Weight Spring P/N 206663
A genuine Petter PH governor weight spring.
Petter P/N 206663
Used on the camshaft governor weights, two fitted per engine but sold singularly.
£8.22
Petter PH Fuel Pump Rack Extension Spring
Petter PH fuel pump rack extension spring.
Equivalent to Petter part numbers MJD46 and 256311
£10.50
Market price: £16.57
save 37%
including VAT
Swivel Union Plug / Banjo Bolt 1/4" BSP
A good quality 1/4" BSP swivel union plug / banjo bolt.
Equivalent to Petter P/N 831026
Suitable for use on the fuel filter assembly 284359 as commonly used on Petter AV, AVA, PH, PHW and Lister LD, SL, SR, ST engines etc.
Plated for corrosion resistance.
£5.10
Market price: £10.16
save 50%
including VAT
Petter AV, AVA, PH & PHW Fuel Injector Nozzle HL130S26C175P3
Quality Bryce compatible fuel injector Nozzles, suitable for use on Petter AV, AVA, PH & PHW single and multi cylinder engines.
Equivalent to HL130S26C175P3
£17.76
including VAT
Petter PH, Bryce Fuel Injector
Quality refurbished Bryce 99/208 fuel injectors, suitable for use on Petter PH and PHW single and multi cylinder engines.
These fuel injectors have been fully refurbished with new nozzles and are supplied with all required sealing washers for the nozzle and pipe connections.
Injector body type NSDLA067D0468
Fitted with nozzle HL130S26C175P3
Set at a pressure of 3150 PSI for engines in the 1100 to 2000rpm range.
These injectors fit onto pumps FA0AB080C0210, FA0AB080C0215 and FA0AB080C0770
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£75.00
including VAT
Petter PH, Bryce Fuel Injector - Slow Speed
Quality refurbished Bryce 99/207 fuel injectors, suitable for use on Petter PH, PHW and PJ single and multi cylinder engines.
These fuel injectors have been fully refurbished with new nozzles and are supplied with all required sealing washers for the nozzle and pipe connections.
Injector body type NSDLA067D0468
Fitted with nozzle HL130S26C175P3
Set at a pressure of 2205 PSI for engines in the 900 to 1099 rpm range.
These injectors fit onto pumps FA0AB080C0210, FA0AB080C0215 and FA0AB080C0770
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£75.00
including VAT
Petter PH Fuel Injector Cooling Fin Sleeve P/N 287267
Aluminium cooling fin sleeves for use with 99/208 type injectors fitted to Petter PH engines.
Genuine Lister Petter part number 287267
£65.41
including VAT
Lister Petter PH2 Fuel Lift Pump
Lister Petter Fuel Lift Pump, Equivalent to Lister part number 361451, AC461-299 and BCD 2609/1, 250-66422, 7990262
Fitted to Petter PH2 models.
These lift pumps have a two hole fixing.
£17.10
Market price: £120.67
save 86%
including VAT
Bryce, Petter Fuel Pump FAOAB080C0210
Refurbished Bryce fuel injection pumps suitable for use on Petter PH and PHW single and multi cylinder engines.
These fuel injection pumps are suitable replacements for pumps marked FAOAB080C0210 and A1AA80/6S210A.
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£132.00
including VAT
Bryce, Petter Fuel Pump FAOAB080C0215
Click here
to subscribe for 'Back-in-stock' notifications
Quality refurbished Bryce fuel injection pumps suitable for use on Petter PH and PHW marine single and multi cylinder engines.
These fuel injection pumps are suitable replacements for pumps marked FAOAB080C0215.
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£132.00
including VAT
Click here
to subscribe for 'Back-in-stock' notifications
Bryce, Petter Fuel Pump FAOAB080C0700
Click here
to subscribe for 'Back-in-stock' notifications
Quality refurbished Bryce fuel injection pumps suitable for use on Petter PH & PHW single and multi cylinder engines.
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£132.00
including VAT
Click here
to subscribe for 'Back-in-stock' notifications
Bosch, Petter PH & PHW Fuel Pump - FAOAB080C0770 Replacement
A genuine Bosch 9-410-031-021 fuel injection pump which has been carefully modified to be suitable for use on Petter PH and PHW single and multi cylinder engines.
These Bosch fuel injection pumps have been completely stripped to a bare pump casting which we have then modified by machining the body in our own machine shop to equip them with brass rack bushes more commonly found on the Bryce series of pumps so that they can be equipped with rubber bellows to prevent the ingress of dust and dirt etc. They are then reassembled with a new rack and an 8mm element and fully tested in our own fuel injection workshop to be a direct equivalent / replacement of the Bryce FAOAB series fuel pumps.
Given the increasing shortage of original Bryce pumps for Petter applications these Bosch fuel pumps make a cost effect solution for the replacements of any of the below pump numbers.
FAOAB080C0210
FAOAB080C0215
FAOAB080C0280
FAOAB080C0295
FAOAB080C0295
FAOAB080C0700
FAOAB080C0705
FAOAB080C0770
£90.00
including VAT
Bryce, Petter Fuel Pump FAOAB080C0770
Quality refurbished Bryce fuel injection pumps suitable for use on Petter PH and PHW single and multi cylinder engines.
These fuel injection pumps are suitable replacements for and supersede all Bryce pumps identified with the following numbers.
FAOAB080C0210
FAOAB080C0215
FAOAB080C0280
FAOAB080C0295
FAOAB080C0295
FAOAB080C0700
FAOAB080C0705
FAOAB080C0770
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£132.00
including VAT
Bosch PF1A, Indian Petter Fuel Pump - Bosch 9410031021
New Bosch PF1A fuel injection pumps suitable for use on Indian built Kirloskar / Petter clone engines such as the AV, AVA, PH, PHW, TV1, TV2 and DM20 series of single and multi cylinder engines.
These fuel injection pumps are not suitable as replacements for British made engines fitted with Bryce pumps.
Please note that the reconditioned products are supplied on a service exchange basis, there will be a surcharge plus VAT
£78.00
including VAT
Bryce FAOAB Fuel Pump Rebuild Kit
A high quality Bryce fuel injection pump rebuild kit suitable for use on the FAOAB and A1AA series of fuel pumps.
These fit the fuel pumps used on many of the Petter single and multi cylinder engines including but not limited to the AV, AVA, PH, PHW as well as the Petter PJ and PJW series engines.
These fuel injection pump rebuild kits are suitable replacements for all Bryce pumps identified with the following numbers.
FA0AB080C0210
FA0AB080C0215
FA0AB080C0280
FA0AB080C0295
FA0AB080C0700
FA0AB080C0705
FA0AB080C0770
£39.98
including VAT
Bryce FAOAB, Petter Fuel Pump Control Rod / Rack P/N 1-153
Quality Bryce control rod / rack suitable for use on the FAOAB type fuel pumps used on many Lister and Petter single and multi cylinder engines including but not limited to the Petter PH and the Petter PJ series engines with an 8.0mm element.
The rod is 9mm diameter and 102mm in length
Fits the following pumps:
FAOAB080C0210
FAOAB080C0215
FAOAB080C0700
FAOAB080C0705
FAOAB080C0770
FAOAB080C0280
FAOAB080C0295
£27.60
including VAT
Bryce Type Fuel Pump Rubber Bellows
Quality Bryce type fuel injection pump rubber bellows as used on many of the fuel pumps fitted to Petter single and multi cylinder engines including but not limited to the Petter PH and the Petter PJ series engines.
These fuel injection pump bellows are suitable replacements for Petter P/N 367900 and fit the following pump types and other not listed.
There are 2 fitted to each pump on the engine. Sold Individually
FA0AB080C0210
FA0AB080C0215
FA0AB080C0700
FA0AB080C0705
FA0AB080C0770
FA0AB080C0280
FA0AB080C0295
£4.99
including VAT
Petter Fuel Pump Delivery Valve Washer Bryce P/N 13/82
A quality fuel pump delivery valve washer measuring 17.8mm x 12.5mm x 3.0mm.
These delivery valve washers are suitable for use in Bryce FAOAB series fuel pumps as fitted to Petter AV, AVA, PH, PHW, PJ and PJW engines.
These delivery valve washers are suitable for use in Bryce FAOAB series fuel pumps as fitted to Petter AV, AVA, PH, PHW, PJ and PJW engines.
Equivalent to: Bryce P/N 13/82
NB:- These washers may be supplied in fibre or nylon materials depending on stock availability at the time of your order.
£3.60
including VAT
Petter PH, Bryce 210 & 177 Fuel Pump Delivery Valve
Quality Bryce type fuel pump delivery valves.
These delivery valves are suitable for use in Bryce FAOABO80210 and FAOABO70CO177 fuel pumps as commonly used on Petter PH and PHW single and multi cylinder engines.
These delivery valves are suitable for use in Bryce FAOABO80210 and FAOABO70CO177 fuel pumps as commonly used on Petter PH and PHW single and multi cylinder engines.
These delivery valves only fit into Bryce FA0AB080C0210 and FAOABO70CO177 type pumps.
£15.00
including VAT
Petter Fuel Pump Element 8mm Bryce 1/559
Quality Bryce type fuel pump elements.
These 8mm 1/559 elements are suitable for use in Bryce FAOABO80C0210, FAOABO80C0280 and FAOABO80CO770 fuel pumps as commonly used on Petter PH, PHW and PJ single and multi cylinder engines.
These 8mm 1/559 elements are suitable for use in Bryce FAOABO80C0210, FAOABO80C0280 and FAOABO80CO770 fuel pumps as commonly used on Petter PH, PHW and PJ single and multi cylinder engines.
These elements only fit into Bryce FA0AB080C0210, FAOABO80C0280, FAOABO80CO700 and FAOABO80CO770 type pumps.
£24.00
including VAT
Petter Fuel Pump Delivery Valve, Bryce 1/598
Quality Bryce type fuel pump delivery valves.
These delivery valves are suitable for use in Bryce FAOABO80C0280, FAOABO80C0700 & FAOABO80C0770 fuel pumps as commonly used on Petter PH, PHW and PJ single and multi cylinder engines.
These delivery valves are suitable for use in Bryce FAOABO80C0280, FAOABO80C0700 & FAOABO80C0770 fuel pumps as commonly used on Petter PH, PHW and PJ single and multi cylinder engines.
£15.00
including VAT
Petter AV, AVA, PH & PHW Fuel Pump Overload Stop Assembly P/N 95399
Click here
to subscribe for 'Back-in-stock' notifications
Petter AV, AVA, PH and PHW fuel pump overload stop assembly
This part attaches to the end of the fuel pump rack to form the overload stop mechanism.
Petter P/N 95399
These are in new, old stock / good used condition.
£18.00
including VAT
Click here
to subscribe for 'Back-in-stock' notifications
Petter AV, AVA, PH & PHW Fuel Pump Rack Extension P/N 250882
Petter AV, AVA, PH and PHW fuel pump rack extension fork.
This brass part attached to the end of the fuel pump rack to form part of the overload stop mechanism.
Petter P/N JA69, 250881, 250882 and 251207
£7.20
including VAT
Swivel Union Plug Banjo Bolt P/N 201-53400
Lister style swivel union plugs / banjo bolts equivalent to Lister P/N 201-53400
Suitable for use on the Bryce FAOABO series cast iron bodied fuel pumps as fitted to the Lister LD, SL, SR and ST series engines.
Threaded 1/4" BSP 19TPI.
£5.99
Market price: £13.05
save 54%
including VAT
Petter Type Fuel Tank
A good quality copy of the later type Petter 11 litre fuel tank complete with a cast iron mounting bracket and tank straps, could be used for any engine in need of a well made fuel tank.
The tank has a 1/4" BSP female threaded union on the bottom at one end for the fuel take off and a banjo style fitting in the top for the injector bleed off return pipe. This could easily be blanked off if not required.
£62.40
including VAT
Petter PH Fuel Tank Cap 2.5" Cam Type
Fuel tank cap, 2.5" cam type suitable for Petter PH1 and PH2 air cooled engines.
Lister Petter part number 266555.
£35.87
including VAT
Brass Fuel Filter Mesh
A fine brass fuel filter mesh suitable for use in fuel tanks and filter assemblies. Also found in fuel taps and carburetor float chambers.
£3.98
including VAT
Banjo Fitting 10mm
Good quality banjo fittings suitable for use on the top of our Lister CS fuel tank kits for the injector leak off return and also most of the Petter type fuel systems.
Offers flexibility when you might want to form custom fuel lines for your own individual setup.
Plated for corrosion resistance.
£5.10
including VAT
Lister Diesel Engine Spares
Lister CS Engine Spares
Lister Petrol Engine Spares
Petter Diesel Engine Spares
Petter Petrol Engine Spares
Paragon Paint Products
Gaskets & Gasket Sets
Magneto Spares & Ignition
Fuel Injection
Water Pumps & Spares
Stationary Engine Books & Transfers
Starting Handles (21)
Wolseley Engine Spares (35)
Ruston Hornsby Spares (31)
Stuart Turner Spares (8)
Fowler Engine Spares (2)
Associated / Amanco Engine Spares (14)
Crossley Engine Spares (6)
Brass Fuel Cocks & Water Drain Taps
Sight Feed Lubricators & Oil Level Gauges
Piston Rings - Loose
Alternators, Invertors, Base Plates & AVM's
Transmissions - Pulleys & Belts
Gasket Materials & Gland Packing
Fixings - Nuts, Bolts & Studs
Workshop Consumables
Tools (27)
Plastigauge
Clearance Corner (4)
Genuine Lister Parts stock
Lister Petter Engine Data
Peter Slater Fuel Injection Engineers Data Archive
