Equivalent to Lister Petter part number 088-02177
Suitable for both original Lister CS engines and Indian Listeroid engines.
Equivalent to Lister Petter part number 008-02178
A pair of new felt crankshaft oil seals, suitable for use on older original Lister CS engines of all sizes and Indian Listeroid engines which use the original style bush bearings.
Equivalent to Lister P/N: 003-00664
A single gasket for the crank case breather plate on all CS engines.
It is a good idea to replace this when changing the breather diaphragm to ensure your crankcase vacuum is maintained to prevent oil leaks.
A single gasket for the crank case breather assembly on all Lister CS engines.
This gasket sits between the breather elbow and the crankcase inspection door.
Equivalent to Lister P/N 003-00309
Brand new, old stock Lister compression change over valve plug copper sealing washer for the CS, JP, JK & JS range of engines.
The Lister part number is 010-03006.
New, old stock Lister compression change over valve plug copper sealing washer for the CS, JP, JK & JS range of engines.
The Lister part number is 010-03091
Quality aluminium bearing shims, available in three thicknesses to allow for the fine adjustment of your Lister CS crankshafts end float. Particularly useful for anyone wishing to convert their genuine Lister engine to the taper roller bearing system as this conversion necessitates the shimming up of the bearing carriers away from the crankcase by approximately 0.020" either side.
Two types are available, small for the old style engines with four mounting studs points on the tear drop shaped bearing carrier and large one for the Indian variants usually found on engines fitted with taper roller bearings using bearing carriers with five mounting stud points.
These shims should ideally be inter spaced between gaskets of the same type made from paper which are supplied in our gull gasket sets or they can be used without paper gaskets if every layer is bonded with a jointing compound such as Heldite.
High quality aluminium or paper cylinder base shims available in a variety of thicknesses to allow for the fine adjustment of your Lister CS's bump clearance.
These aluminium shims should ideally be inter spaced between gaskets of the same type made from paper which are supplied in our full gasket sets or loose from this listing. The aluminium shims can be used without paper gaskets in between if every layer is bonded together with a jointing compound such as Heldite.
A single gasket for the camshaft end cover on single cylinder Lister CS engines.
Lister Petter P/N 003-00153
A gasket for the cylinder water jacket access door on all Lister CS engines.
Equivalent to Lister P/N 026-00112.
A good quality die cut water flange gaskets for all Lister CS, JP and Listeroid CS type engines.
Equivalent to Lister P/N 010-02059
Good quality die cut gaskets for the air inlet manifold to cylinder head joint on all Lister CS and Listeroid engines.
Made from high quality asbestos free composite gasket material.
A genuine Lister die cut gasket for the top cover of the wick style fuel filter housing as used on Lister CS and JP engines.
Lister P/N 023-02278
A high quality die cut gasket for the exhaust joint on all Lister CS, J, L and JP engines.
Lister P/N 003-00307 or 010-03057
A single gasket for the crank case access door on all single cylinder genuine Lister CS, L and J engines.
These will not fit onto twin cylinder engines or Indian build clone engines.
Click here
to subscribe for 'Back-in-stock' notifications
High quality overhaul gasket sets suitable for use on genuine Lister CS engines, models 5-1, 6-1 and 8-1.
Equivalent to Lister Petter part number 657-10392.
Not suitable for the 3-1, 3.5-1 and twin cylinder models.
High quality overhaul gasket sets suitable for use on genuine Lister CS engines, models 3-1 and 3.5-1.
Equivalent to Lister Petter part number 657-10370
Not suitable for the other CS models which have a 4.5" cylinder bore and therefore utilise a different head gasket.
High quality de-coke gasket sets suitable for use on genuine Lister CS engines, models 5-1, 6-1, 8-1, 10-2, 12-2 and 16-2.
Equivalent to Lister Petter part number 657-10380. Two sets will be required for the twin cylinder models.
Not suitable for the 3-1 and 3.5-1 models.
High quality de-coke gasket sets suitable for use on genuine Lister CS engines, models 3-1 and 3.5-1.
Equivalent to Lister Petter part number 657-10360.
Not suitable for the other CS models which have a 4.5" cylinder bore and therefore utilise a different head gasket.
Click here
to subscribe for 'Back-in-stock' notifications
A quality copper and non asbestos sandwich head gasket suitable for use on Lister CS 3-1 and 3.5-1 engines.
Lister Diesel Engine Spares
Lister CS Engine Spares
Lister Petrol Engine Spares
Petter Diesel Engine Spares
Petter Petrol Engine Spares
Paragon Paint Products
Gaskets & Gasket Sets
Magneto Spares & Ignition
Fuel Injection
Water Pumps & Spares
Stationary Engine Books & Transfers
Starting Handles (22)
Wolseley Engine Spares (35)
Ruston Hornsby Spares (32)
Stuart Turner Spares (8)
Fowler Engine Spares (2)
Associated / Amanco Engine Spares (16)
Crossley Engine Spares (6)
Brass Fuel Cocks & Water Drain Taps
Sight Feed Lubricators & Oil Level Gauges
Piston Rings - Loose
Alternators, Invertors, Base Plates & AVM's
Transmissions - Pulleys & Belts
Gasket Materials & Gland Packing
Fixings - Nuts, Bolts & Studs
Workshop Consumables
Tools (27)
Plastigauge
Clearance Corner (3)
Genuine Lister Parts stock
Lister Petter Engine Data
Peter Slater Fuel Injection Engineers Data Archive
