Anand Enterprise

British standard fine (BSF) self colour steel nuts available in sizes from 3/16" to 5/8".

Please click on this product to select size and quantity required.

The exact colour can vary dependent upon supplier and batch held in stock at any one time.

A quality 5/16" by 3/4" long BSF set screw / bolt.

Equivalent to Petter P/N JD31, 722025 and 327492

This is the correct size set screw for securing the camshaft extension shafts and inlet / exhaust manifolds on Petter AV, AVA, PH and PHW engines.

A quality 3/8" by 1/2" long whitworth bolt. This size is commonly used on the Lister CS engines but could be used for any application requiring this size of Whitworth bolt.

For suitable sized nuts please see the Whitworth nuts section.

A quality 5/16" by 5/8" long Whitworth (BSW) bolt / setscrew.

A quality 3/8" by 3/4" long whitworth bolt. This size is commonly used on the Lister CS engines but could be used for any application requiring this size of Whitworth bolt.

For suitable sized nuts please see the Whitworth nuts section.

Quality whitworth bolts commonly found on the crankcase breather of the Lister CS engines and also suitable for the exhaust flange of Lister D engines but could be used for any application requiring this size.
 

A single gasket for the crank case breather assembly on all Lister CS engines.

This gasket sits between the breather elbow and the crankcase inspection door.

Equivalent to Lister P/N 003-00309

Quality aluminium bearing shims, available in three thicknesses to allow for the fine adjustment of your Lister CS crankshafts end float. Particularly useful for anyone wishing to convert their genuine Lister engine to the taper roller bearing system as this conversion necessitates the shimming up of the bearing carriers away from the crankcase by approximately 0.020" either side.

Two types are available, small for the old style engines with four mounting studs points on the tear drop shaped bearing carrier and large one for the Indian variants usually found on engines fitted with taper roller bearings using bearing carriers with five mounting stud points.

These shims should ideally be inter spaced between gaskets of the same type made from paper which are supplied in our gull gasket sets or they can be used without paper gaskets if every layer is bonded with a jointing compound such as Heldite.

A gasket for the camshaft end cover on single cylinder Listeroid CS engines.

A pair of genuine Lister circlips for the gudgeon pin of Lister 3-1 & 3.5-1 CS engines.

Lister P/N 208-00216

Lister CS gudgeon pin circlips.

Lister P/N 008-00410

Two sizes are available:-

Standard size for all engines on a 4.5" cylinder bore which excludes the Indian 12-1 & 24-2 engines
Extra large specifically for the Indian Listeroid 12-1 & 24-2 engines.

Please select the size required from the menu.

Quality BSF studs, commonly found on Petter engines but could be used for any application requiring this size.

Quality Whitworth studs, commonly found on the camshaft cover, oil filler flap, crank case door and breather bend of the Lister CS engines but could be used for any application requiring this size.

Quality BSF studs, commonly found on Petter engines but could be used for any application requiring this size.

Quality BSF studs, commonly found on Petter engines but could be used for any application requiring this size.

Quality BSF studs, commonly found on Petter engines but could be used for any application requiring this size.

No.4 x 1/4" Hammer Drive Screws / Rivets.

Brass electro plated finish.

To suit Lister engine name plates. Pack of 20 (Approx)

The head diameter = 5mm, shank diameter = 2.9mm

Quality Whitworth studs commonly found on Lister CS engines but could be used for any application requiring this size.

Taper pins suitable for use on all CS cam shafts, two lengths are available.

Quality BSF studs, commonly found on Petter engines but could be used for any application requiring this size.